Tired of Removing Paint to Inspect Welds?

By Decibel -

Removing Paint is Time Consuming and Expensive

For decades, legacy NDT methods, such as penetrant and magnetic particle inspection, required that paint be removed from parts before they could be inspected. The paint was often removed using harsh chemicals. Over time, increasingly strict government regulations about chemical safety and waste treatment have caused the cost of paint removal to rise dramatically. As the cost of paint removal increases so does the overall cost of inspection.

Inspect Through Paint with Dynamic Lift-Off Compensation Technology

The use of a flexible PCB probe with cross-wound coil technology combined with dynamic lift-off compensation makes it possible to detect surface-breaking cracks through paint, resulting in significant time and cost savings.

The principle of dynamic lift-off compensation.
 

Our MagnaFORM™ probe features dynamic lift-off compensation and helps make weld inspection fast and efficient. The dynamic lift-off compensation helps the probe maintain sensitivity to surface-breaking cracks. All of the channels perform lift-off compensation in real time. Now, we can inspect through paint up to 3 mm thick.

The MagnaFORM probe.
 

The MagnaFORM probe enables you to inspect through painted surfaces.
 

The MagnaFORM Probe Delivers Results

The example below demonstrates that the MagnaFORM probe provides you with clear images through paint for indications with the same lengths and same depths located on different areas of welded parts. The amplitude of the signals is the same for each location, demonstrating consistent defect detection in all locations.

A C-scan image using a MagnaFORM probe of EDM notch indications at different locations.
 

Don't spend valuable resources on stripping and repainting surfaces as part of your inspection process. With eddy current array technologyand the advanced features of the MagnaFORM probe, you can inspect welds and surfaces through paint, helping you save time and reduce cost. To learn more,check out this video about the MagnaFORM solution.

Popular posts from this blog

What is the Plate Lamination Defect?

By Decibel -
Image
Plate lamination defect is one of the primary processing discontinuity that originates during hot or cold forming processes and is considered as a serious metal plate defect.  All the metals contain discontinuities at micro and macro levels. These discontinuities, when above the acceptance level, are termed as defects. The discontinuities in metal are classified according to the stage of manufacturing in which they initiate.  Plate lamination defect can be defined as flat and thin subsurface separations present inside metal plate, parallel to the surface of the plates. The sources of this defect are inherent discontinuities present in metal such as inclusion and porosity, which are flattened during the rolling process.  Carbon Steel Plate Lamination Defect & Reasons A carbon steel plate is produced by the process of hot or cold rolling a thick slab. During this process, carbon steel may pass through the rollers many times to achieve the desired thickness. Each pass results in
Read more

Comparison of the use of rutile and cellulosic electrodes Knowledge Sharing From Decibel.

By Decibel -
Image
Comparison of the use of rutile and cellulosic electrodes Types of electrodes and their compositions Many types of manual metal arc (MMA) electrodes are available on the market. Depending on the main constituent of their flux, they are grouped into three categories: cellulosic, rutile and basic. All electrodes consist of a cored wire (typically 2.5–6mm diameter) coated by a flux. The core wire is generally made of low-quality riming steel and the fluxes contain many elements allowing refinement of the weld macrostructure. The composition of the flux impacts the electrodes’ behaviour. The main constituents of the different types of electrodes and the shielding gas created for each are described in Table 1 (Bowniszewski, 1979). Table 1 Main constituent of the three possible types of electrodes and shielding gas created by its combustion. Electrode type Main constituent Shielding gas created Rutile Titania (TiO2) Mainly CO2 Basic Calcium compounds Mainly CO2 Cellulosic
Read more

CSWIP Preparatory Classes in Kerala with 90 % Pass Rate.

By Decibel -
Image
Decibel Conducts CSWIP 3.1 Preparatory Courses in Kerala at Trivandrum and Pattambi Training Centers. Overall a 90% Pass rate yearly has been achieved regularly and Intensive Practicals for Understanding the concepts, familiarizing with the technology and crafting a welding inspector from RAW has been done always, by our expert faculty members. You may See the Qualified Faculties at our End for Understanding more on our Team. After Successful Completion of the Training & Examination you will be getting Free Placement Support for Enrich your career towards the next stage of your qualification. If you Fail in CSWIP 3.1 Exam we will provide Free of Cost Additional Training for you Till you Get Passed. Contact Decibel For More Details on 100% Pass for CSWIP 3.1
Read more